Daihatsu Domino C1396 Engine Trouble Code

Chassis Code C1396

What is Daihatsu Domino C1396?

Daihatsu Domino C1396 code can indicate a faulty oxygen sensor, which may eventually damage the catalytic converter (repair cost: $2,000–$2,200). Professional diagnosis costs around $200–$210. Oxygen sensors are often straightforward to replace — check your owner's manual for location and instructions. This issue should be addressed promptly to prevent further damage.

C1396 on the Daihatsu Domino

The Daihatsu Domino is particularly susceptible to C1396 faults when the engine management unit receives conflicting sensor data. Owners report that C1396 on Daihatsu Domino most commonly surfaces after 60,000 miles, especially when routine service intervals have been missed.

C1396 Daihatsu Domino Engine Diagram

Code Information

Code Type:OBD-II Chassis (C) Trouble Code
System:Chassis
Vehicle:Daihatsu Domino
Brand:Daihatsu
Model:Domino
Code:C1396

C1396 Daihatsu Domino Symptoms

⚠️

Check Engine Light

Illuminated Daihatsu Domino dashboard warning

🔧

Engine Stalling

Engine stops unexpectedly or misfires

Performance Issues

Reduced power or acceleration on the Daihatsu Domino

🚫

Starting Problems

Difficulty starting the engine

Poor Fuel Economy

Increased fuel consumption on the Daihatsu Domino

💨

Increased Emissions

Failed emissions test due to C1396

C1396 Code Structure

Understanding what each digit means in the C1396 chassis trouble code:

C 1 3 9 6
Chassis Code Fuel And Air Metering Throttle/Pedal Position Sensor/Switch A Circuit Intermittent Crankshaft Position Sensor A Circuit Malfunction Ignition Coil A Primary/Secondary Circuit Malfunction

How to Fix Daihatsu Domino C1396

Diagnostic Steps:

Regarding C1396, carefully inspect the wire harness near the intake manifold bracket, best accessed from below near the oil filter. Look for chafing, pinching, or damaged insulation.

Repair Solution:

Disconnected, dirty, or fouled spark plugs commonly prevent proper engine operation. Replace spark plugs every season or 25 hours. Verify proper spark plug gap. If plugs are good, check ignition components: spark plug wires, coils, and ignition module.

Technical Notes:

Parts or components should not be replaced based solely on C1396 DTC. Consult your vehicle service manual for proper diagnostic procedures, possible causes, and required testing before replacement.

Daihatsu Domino C1396 Repair Cost

Torque converter clutch solenoid replacement on the Daihatsu Domino — relevant for owners who tow regularly — costs $280–$480. A full transmission fluid change ($120–$160) at the same service is recommended because contaminated fluid accelerates solenoid wear.

C1396 Description

C1396 engine trouble code is related to Ignition Coil A Primary/Secondary Circuit Malfunction.

Main Cause

The primary reason for C1396 OBD-II Engine Trouble Code is: Throttle/Pedal Position Sensor/Switch A Circuit Intermittent.

Common C1396 Misdiagnosis on the Daihatsu Domino

On the Daihatsu Domino, the EGR cooler is sometimes replaced for C1396 when the EGR valve position sensor is at fault. The two components share a fault pathway in older scan tools that do not display live EGR valve position data.

DIY Repair Guide: C1396 on Daihatsu Domino

For the Daihatsu Domino, an EGR valve inspection is a useful DIY step before spending money on diagnosis. Remove the valve (2–4 bolts depending on generation), inspect for carbon build-up, and use carburettor cleaner and a soft brass brush to clean the valve face and seat.

Preventing C1396 on the Daihatsu Domino

The Daihatsu Domino coolant temperature sensor plays a role in fuel enrichment during warm-up. Replacing it as a precaution at 80,000 miles ($25–$40 DIY) prevents the faulty cold-start enrichment that can lead to C1396.

Frequently Asked Questions — Daihatsu Domino C1396

Q: Will C1396 cause my Daihatsu Domino to fail an emissions test?
A: Yes. Any stored fault code — including C1396 — will cause an automatic failure in most OBD-II based emissions tests. The code must be resolved and the vehicle must complete a full OBD drive cycle with no new codes before the test.

Search Another Code